If you don’t know How to Tile a Shower wall then this guide will let you know how to do it. Although, It is a very simple process, but requires some preparations. With the help of the 9 steps mentioned below will produce an outstanding result. So Check these out.
How to tile a shower wall?
To tile a shower you need to be aware of two things like what to do and how to do it. The what to do part is clear here but the how to do part needs to be resolved. It can be best resolved by breaking it into a few parts. The few parts are first you need to tear down your shower to scratch. Then take the measurements of your shower. After that cut and paste the tiles and put every required part in its place. Finally, doing the grouting and giving the shower a good finish.
Also Check: How to Build a Floating Deck in 2023 [Floating Deck Ideas]
There are a few things that can be done to tile a shower wall. Once the demolition of the old tile is complete, start preparing the shower space by installing a cement backer board in the shower area. Later measure and dry lay tiles for shower walls. After that, set tiles on the shower walls and shower sidewalls. If cutting of tiles is required in the shower then cut and set the cut pieces. Finally, try to complete the shower walls with a thin set and grouting.
5 Things Before Installing a Tile on a Shower Wall
Things that you should be aware of before installing a shower wall are as follows;
- You should first decide on what material you want to use, like Ceramic, Porcelain, or Marble.
- Pick a color palette.
- Vary the scale and pattern
- Grouting is important(make sure you use the right type of grout, unsanded grout is for marble tile and small grout lines, and sanded grout is for wider joints)
- Choose the right mortar(this is specifically for porous tiles, like stone, the color of the stone you are using and the color of the mortar should be used.)
Check: How to Clean a Water Cooler in 2023 [4 Tested Methods]
Equipment Required
The following equipment should be used to tile a shower wall.
- Tile cutter
- Grout Float
- Grout Sponge
- Notched Trowel
- Tile Nippers
- Chalk line
- Bubble level
- Rubber Mallet
- Plastic Buckets
9 Steps to Tile a Shower Wall
The following 9 steps should be followed to tile a shower wall properly.
Check shower stud walls – Before anything is done it’s better to check the stud walls are plumb and level. Take a 4-foot level and place it across all the studs. Do this vertically horizontally and diagonally.
Use waterproofing material behind the tile – It is very critical and essential to use waterproofing material behind a tile, there are many ways to waterproof a shower, some are; RedGard with Cement Board, ARDEX 8+9 with Cement Board, Hydro ban with Cement Board, Wedi Building Panels, etc.
Use waterproofing material behind the tile
Plan Tile Layout – once the waterproofing is done, it’s better to move on to the part of laying the tile out. Nothing fancy but just a pen or pencil is just fine to do this job. The reason for the layout is two-fold, first is to prevent slivers of tiles at the ceiling or corners and it will give you the plan to follow.
Purchase Quality Porcelain Tile – solid porcelain tile is a better choice as it’s the same color throughout and chipping a bit of it won’t make a difference.
Read: 10 Best Floating Shelves Ideas for Home in 2023
Tile Leveling Systems for Large Format Tiles – tiles are getting larger and are not always perfect and everyone has a hard time getting tiles flushed to each other if they are bowed or cupped. Thus, the tile leveling system helps with tile imperfections.
Stagger Large Format Tiles in Thirds – large tiles tend to cup ar bow upwards in the middle of the tile, this, in turn, creates a slight lip between two adjacent tiles. The staggering of tiles in thirds helps limit this effect.
Use Small Grout Joints – the small grout joints look better and require less cleaning over time.
Quality thin-sets – use the best thin-set available in the market so that there is no problem in the future, for ex- X77.
Quality Grouts – like the thin-set the best grout should be used for no problems in the future like Bostik’s QuartzLock 2.
Visit: 10 Creative Ideas for Papasan Cushion Cover in 2023
Frequently Asked Questions
What do you put behind a tile in a shower?
The waterproofing coat should be always put behind the tile in the shower to protect the walls of the house.
Do I need to waterproof shower walls before tiling?
Yes, it is very essential because if the waterproofing is not done the walls will get wet and the seeping water can cause a lot of damage in the house.
So this is all for this guide on How to Tile a Shower wall. If you want to ask anything related to this guide then comment down below, and for more information keep visiting itshomely.com.